1.1 These test methods cover the determination of water vapor transmission rate (WVTR) of materials, such as, but not limited to, paper, plastic films, other sheet materials, coatings, foams, fiberboards, gypsum and plaster products, wood products, and plastics. Two basic methods, the Desiccant Method and the Water Method, are provided for the measurement of WVTR. In these tests, the desired temperature and side-to-side humidity conditions, with resultant vapor drive through the specimen, are used. The test conditions employed are at the discretion of the user, but in all cases, are reported with the results.
1.2 The values stated in either Inch-Pound or SI units are to be regarded separately as standard. The values stated in each system are not necessarily exact equivalents; therefore, each system shall be used independently of the other. Derived results are converted from one system to the other using appropriate conversion factors (see Table 1).
1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM E96/E96M-22a Referenced Document
ASTM C168 Standard Terminology Relating to Thermal Insulation
ASTM C1809 Standard Practice for Preparation of Specimens and Reporting of Results for Permeance Testing of Pressure Sensitive Adhesive Sealed Joints in Insulation Vapor Retarders
ASTM D2301 Standard Specification for Vinyl Chloride Plastic Pressure-Sensitive Electrical Insulating Tape
ASTM D449/D449M Standard Specification for Asphalt Used in Dampproofing and Waterproofing*, 2024-04-21 Update
ASTM E177 Standard Practice for Use of the Terms Precision and Bias in ASTM Test Methods
ASTM E691 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method
ASTM E96/E96M-22a history
2024ASTM E96/E96M-24 Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials
2023ASTM E96/E96M-23 Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials
2022ASTM E96/E96M-22ae1 Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials
2022ASTM E96/E96M-22a Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials
2022ASTM E96/E96M-22 Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials
2021ASTM E96/E96M-21 Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials
0000 ASTM E96/E96M-20
2016ASTM E96/E96M-16 Standard Test Methods for Gravimetric Determination of Water Vapor Transmission Rate of Materials
2015ASTM E96/E96M-15 Standard Test Methods for Water Vapor Transmission of Materials
2014ASTM E96/E96M-14 Standard Test Methods for Water Vapor Transmission of Materials
2013ASTM E96/E96M-13 Standard Test Methods for Water Vapor Transmission of Materials
2012ASTM E96/E96M-12 Standard Test Methods for Water Vapor Transmission of Materials
2010ASTM E96/E96M-10 Standard Test Methods for Water Vapor Transmission of Materials
2005ASTM E96/E96M-05 Standard Test Methods for Water Vapor Transmission of Materials
2000ASTM E96-00e1 Standard Test Methods for Water Vapor Transmission of Materials
2000ASTM E96-00 Standard Test Methods for Water Vapor Transmission of Materials
1995ASTM E96-95 Standard Test Method for Water Vapor Transmission of Materials
1990ASTM E96-90 Standard Test Method for Water Vapor Transmission of Materials