ASTM D5963-22 PDF

Scope: 1.1 This test method covers the measurement of abrasion resistance of rubbers (vulcanized thermoset rubbers and thermoplastic elastomers) that are subject to abrasive/frictional wear in actual service. The abrasion resistance is measured by moving a test piece across the surface of an abrasive sheet mounted to a revolving drum, and is expressed as volume loss in cubic millimetres or abrasion resistance index in percent. For volume loss, a smaller number indicates better abrasion resistance, while for the abrasion resistance index, a smaller number denotes poorer abrasion resistance. 1.2 Test results obtained by this test method shall not be assumed to represent the wear behavior of rubber products experienced in actual service. 1.3 The values stated in SI units are to be regarded as the standard. The values in parentheses are for information only. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D5963-22 Referenced Document

ASTM D1765 Standard Classification System for Carbon Blacks Used in Rubber Products (Standard + Redline PDF Bundle)
ASTM D2240 Standard Test Method for Properties of Rubber &8212; Durometer Hardness*， 2024-04-21 Update
ASTM D297 Standard Test Methods for Rubber Products-Chemical Analysis
ASTM D3182 Standard Practice for Rubber-Materials, Equipment, and Procedures for Mixing Standard Compounds and Preparing Standard Vulcanized Sheets
ASTM D4483 Standard Practice for Determining Precision for Test Method Standards in the Rubber and Carbon Black Industries
ISO 2393 Rubber test mixes - Preparation, mixing and vulcanization - Equipment and procedures
ISO 2781 Rubber, vulcanized or thermoplastic - Determination of density
ISO 4649 Rubber, vulcanized or thermoplastic - Determination of abrasion resistance using a rotating cylindrical drum device
ISO 5725 Precision of test methods; Determination of repeatability and reproducibility for a standard test method by inter-laboratory tests
ISO 7619 Rubber - Determination of indentation hardness by means of pocket hardness meters
ISO 868 Plastics and ebonite - Determination of indentation hardness by means of a durometer (Shore hardness)
ISO 9298 Rubber compounding ingredients - Zinc oxide - Test methods

2022 ASTM D5963-22 Standard Test Method for Rubber Property—Abrasion Resistance (Rotary Drum Abrader)
2019 ASTM D5963-04(2019) Standard Test Method for Rubber Property—Abrasion Resistance (Rotary Drum Abrader)
2004 ASTM D5963-04(2015) Standard Test Method for Rubber Property&x2014;Abrasion Resistance (Rotary Drum Abrader)
2004 ASTM D5963-04(2010)e1 Standard Test Method for Rubber Propertymdash;Abrasion Resistance (Rotary Drum Abrader)
2004 ASTM D5963-04(2010) Standard Test Method for Rubber Property&8212;Abrasion Resistance (Rotary Drum Abrader)
2004 ASTM D5963-04 Standard Test Method for Rubber Property8212;Abrasion Resistance (Rotary Drum Abrader)
1997 ASTM D5963-97a(2001)e1 Standard Test Method for Rubber Property-Abrasion Resistance (Rotary Drum Abrader)
1997 ASTM D5963-97a(2001) Standard Test Method for Rubber8212;Property Abrasion Resistance (Rotary Drum Abrader)
1997 ASTM D5963-97a Standard Test Method for Rubber8212;Property Abrasion Resistance (Rotary Drum Abrader)