ASTM D3385-18
Standard Test Method for Infiltration Rate of Soils in Field Using Double-Ring Infiltrometer

Standard No.

ASTM D3385-18

Release Date

2018

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM D3385-18

Scope

1.1 This test method describes a procedure for field measurement of the rate of infiltration of liquid (typically water) into soils using double-ring infiltrometer. 1.2 The infiltrometer is installed by driving into the soil. The infiltrometer also may be installed in a trench excavated in dry or stiff soils. 1.3 Soils should be regarded as natural occurring soils or processed materials or mixtures of natural soils and processed materials, or other porous materials, and which are basically insoluble and are in accordance with requirements of 1.6. 1.4 This test method is particularly applicable to relatively uniform fine-grained soils, with an absence of very plastic (fat) clays and gravel-size particles and with moderate to low resistance to ring penetration. 1.5 This test method may be conducted at the ground surface or at given depths in pits, and on bare soil or with vegetation in place, depending on the conditions for which infiltration rates are desired. However, this test method cannot be conducted where the test surface is below the groundwater table or perched water table. 1.6 This test method is difficult to use or the resultant data may be unreliable, or both, in very pervious or impervious soils (soils with a hydraulic conductivity greater than about 10−2 cm/s or less than about 1 × 10−5 cm/s) or in dry or stiff soils if these fracture when the rings are installed. For soils with hydraulic conductivity less than 1 × 10−5 cm/s refer to Test Method D5093. 1.7 This test method cannot be used directly to determine the hydraulic conductivity (coefficient of permeability) of the soil (see 5.2). 1.8 Units—The values stated in SI units are to be regarded as the standard. The inch-pound units given in parentheses are mathematical conversions, which are provided for information purposes only and are not considered standard. 1.9 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.10 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D3385-18 Referenced Document

• ASTM D1452 Standard Practice for Soil Investigation and Sampling by Auger Borings
• ASTM D2216 Standard Test Method for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
• ASTM D2488 Recommended Practice for Description Of Soils (Visual-Manual Procedure)
• ASTM D3740 Standard Practice for Minimum Requirements for Agencies Engaged in the Testing and/or Inspection of Soil and Rock as Used in Engineering Design and Construction
• ASTM D5093 Standard Test Method for Field Measurement of Infiltration Rate Using a Double-Ring Infiltrometer with a Sealed-Inner Ring
• ASTM D653 Standard Terminology Relating to Soil, Rock, and Contained Fluids

ASTM D3385-18 history

• 2018 ASTM D3385-18 Standard Test Method for Infiltration Rate of Soils in Field Using Double-Ring Infiltrometer
• 2009 ASTM D3385-09 Standard Test Method for Infiltration Rate of Soils in Field Using Double-Ring Infiltrometer
• 2003 ASTM D3385-03 Standard Test Method for Infiltration Rate of Soils in Field Using Double-Ring Infiltrometer
• 1994 ASTM D3385-94 Standard Test Method for Infiltration Rate of Soils in Field Using Double-Ring Infiltrometer