BS EN ISO 11296-9:2022
Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Lining with a rigidly anchored plastics inner layer
- Standard No.
- BS EN ISO 11296-9:2022
- Release Date
- 2022
- Published By
- British Standards Institution (BSI)
- Latest
- BS EN ISO 11296-9:2022
- Scope
- 1 Scope This document, in conjunction with ISO 11296‑1, specifies the requirements and test methods for pipes and fittings for the renovation of underground non-pressure drainage and sewerage networks by lining with a single rigid annulus of structural cementitious grout formed behind a plastics inner layer. This plastics layer serves as permanent formwork anchored to the grout. This document is applicable to plastics inner layers and grout systems with or without steel reinforcement . It does not apply to the structural design of the lining system. NOTE Systems with multiple annuli are available, but these are controlled by patent rights and not covered by this document.
BS EN ISO 11296-9:2022 Referenced Document
- CEN/TR 14920 Jetting resistance of drain and sewer pipes - Moving jet test method
- EN 10025-1 Hot rolled products of structural steels - Part 1: General technical delivery conditions*， 2024-04-21 Update
- EN 10025-2 Hot rolled products of structural steels - Part 2: Technical delivery conditions for non-alloy structural steels
- EN 1015-3 Methods of test for mortar for masonry - Part 3: Determination of consistence of fresh mortar (by flow table)
- EN 1015-6 Methods of test for mortar for masonry - Part 6: Determination of bulk density of fresh mortar
- EN 1107-2 Flexible sheets for waterproofing - Determination of dimensional stability - Part 2: Plastic and rubber sheets for roof waterproofing
- EN 12814-2 Testing of welded joints of thermoplastics semi-finished products - Part 2: Tensile test
- EN 12814-8 Testing of welded joints of thermoplastics semi-finished products - Part 8: Requirements
- EN 13067 Plastics welding personnel - Qualification testing of welders - Thermoplastics welded assemblies*， 2024-04-21 Update
- EN 13100-4 Non destructive testing of welded joints of thermoplastics semifinished products - Part 4: High voltage testing*， 2024-04-21 Update
- EN 13412:2006 Products and systems for the protection and repair of concrete structures - Test methods - Determination of modulus of elasticity in compression
- EN 14117 Products and systems for the protection and repair of concrete structures - Test methods - Determination of time of efflux of cementitious injection products
- EN 1542:1999 Products and systems for the protection and repair of concrete structures - Test methods - Measurement of bond strength by pull-off
- EN 1610:2015 Construction and testing of drains and sewers
- EN 1916:2002 Concrete pipes and fittings, unreinforced, steel fibre and reinforced*， 2024-04-21 Update
- EN 196-1 Methods of testing cement - Part 1: Determination of strength
- EN 445:2007 Grout for prestressing tendons - Test methods*， 2024-04-21 Update
- ISO 11296-1:2018 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Part 1: General
- ISO 11296-4:2018 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 4: Lining with cured-in-place pipes
- ISO 11296-4:2018/Amd 1:2021 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 4: Lining with cured-in-place pipes — Amendment 1: Updated definitions, marking requirements an
- ISO 11296-7 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks — Part 7: Lining with spirally-wound pipes
- ISO 1133-1 Plastics — Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics — Part 1: Standard method
- ISO 1133-2 Plastics - Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics - Part 2: Method for materials sensitive to time-temperature history and/or moisture
- ISO 11357-6 Plastics - Differential scanning calorimetry (DSC) - Part 6: Determination of oxidation induction time (isothermal OIT) and oxidation induction temperature (dynamic OIT)
- ISO 1183-1 Plastics — Methods for determining the density of non-cellular plastics — Part 1: Immersion method, liquid pycnometer method and titration method
- ISO 12162 Thermoplastics materials for pipes and fittings for pressure applications - Classification, designation and design coefficient
- ISO 13262 Thermoplastics piping systems for non-pressure underground drainage and sewerage - Thermoplastics spirally-formed structured-wall pipes - Determination of the tensile strength of a seam
- ISO 306 Plastics — Thermoplastic materials — Determination of Vicat softening temperature (VST)*， 2022-11-18 Update
- ISO 37 Rubber, vulcanized or thermoplastic - Determination of tensile stress-strain properties
- ISO 4624:2016 Paints and varnishes - Pull-off test for adhesion
- ISO 48-4 Rubber, vulcanized or thermoplastic - Determination of hardness - Part 4: Indentation hardness by durometer method (Shore hardness)
- ISO 4948-2 Steels; Classification; Part 2 : Classification of unalloyed and alloy steels according to main quality classes and main property or application characteristics
- ISO 527-1 Plastics — Determination of tensile properties — Part 1: General principles
- ISO 527-2 Plastics - Determination of tensile properties - Part 2: Test conditions for moulding and extrusion plastics
- ISO 630-1 Structural steels — Part 1: General technical delivery conditions for hot-rolled products
- ISO 630-2 Structural steels - Part 2: Technical delivery conditions for structural steels for general purposes
- ISO 75-2:2013 Plastics - Determination of temperature of deflection under load - Part 2: Plastics and ebonite
BS EN ISO 11296-9:2022 history
- 2022 BS EN ISO 11296-9:2022 Plastics piping systems for renovation of underground non-pressure drainage and sewerage networks - Lining with a rigidly anchored plastics inner layer
