ASTM E1297-08
Standard Test Method for Measuring Fast-Neutron Reaction Rates by Radioactivation of Niobium

Standard No.
ASTM E1297-08
Release Date
2008
Published By
American Society for Testing and Materials (ASTM)
Status
Replace By
ASTM E1297-08(2013)
Latest
ASTM E1297-18
Scope
p>Refer to Practice E 261 for a general discussion of the determination of decay rates, reaction rates, and neutron fluence rates with threshold detectors (1-29). Refer to Practice E 1006, Practice E 185 and Guide E 1018 for the use and application of results obtained by this test method.(34-36)

The half-life of 93mNb is 5730 ± 220 days (30) and has a K X-ray emission probability of 0.1099 ± 0.0025 per decay (30). The Kα and Kβ X-rays of niobium are at 16.521316.152 and 18.61818.953 keV, respectively. The recommended 93Nb (n,n)93mNb cross section comes from the IRDF-90 cross section compendium (31), was drawn from the RRDF-98 cross section evaluations (37) and is shown in Fig. 1.

Chemical dissolution of the irradiated niobium to produce very low mass-per-unit area sources is an effective way to obtain consistent results. The direct counting of foils or wires can produce satisfactory results provided appropriate methods and interpretations are employed. It is possible to use liquid scintillation methods to measure the niobium activity provided the radioactive material can be kept uniformly in solution and appropriate corrections can be made for interfering activities.

The measured reaction rates can be used to correlate neutron exposures, provide comparison with calculated reaction rates, and determine neutron fluences. Reaction rates can be determined with greater accuracy than fluence rates because of the current uncertainty in the cross section versus energy shape.

The 93Nb(n,n)93mNb reaction has the desirable properties of monitoring neutron exposures related to neutron damage of nuclear facility structural components. It has an energy response range corresponding to the damage function of steel and has a half-life sufficiently long to allow its use in very long exposures (up to about 40 years). Monitoring long exposures is useful in determining the long-term integrity of nuclear facility components.

1.1 This test method describes procedures for measuring reaction rates by the activation reaction 93Nb(n,n)93mNb.

1.2 This activation reaction is useful for monitoring neutrons with energies above approximately 0.5 MeV and for irradiation times up to about 30 years.

1.3 With suitable techniques, fast-neutron reaction rates for neutrons with energy distribution similar to fission neutrons can be determined in fast-neutron fluences above about 1016cm2. In the presence of high thermal-neutron fluence rates (>1012cm2·s1), the transmutation of 93mNb due to neutron capture should be investigated. In the presence of high-energy neutron spectra such as are associated with fusion and spallation sources, the transmutation of 93mNb by reactions such as (n,2n) may occur and should be investigated.

1.4 Procedures for other fast-neutron monitors are referenced in Practice E 261.

1.5 Fast-neutron fluence rates can be determined ......

ASTM E1297-08 history

  • 2018 ASTM E1297-18 Standard Test Method for Measuring Fast-Neutron Reaction Rates by Radioactivation of Niobium
  • 2008 ASTM E1297-08(2013) Standard Test Method for Measuring Fast-Neutron Reaction Rates by Radioactivation of Niobium
  • 2008 ASTM E1297-08 Standard Test Method for Measuring Fast-Neutron Reaction Rates by Radioactivation of Niobium
  • 2002 ASTM E1297-02 Standard Test Method for Measuring Fast-Neutron Reaction Rates by Radioactivation of Niobium
  • 1996 ASTM E1297-96 Standard Test Method for Measuring Fast-Neutron Reaction Rates by Radioactivation of Niobium



Copyright ©2024 All Rights Reserved