ASTM D6047-17(2021) Standard Test Methods for Rubber, Raw—Determination of 5-Ethylidenenorbornene (ENB) or Dicyclopentadiene (DCPD) in Ethylene-Propylene-Diene (EPDM) Terpolymers
1.1 These test methods cover the determination of the content of 5-ethylidenenorbornene (ENB) or Dicyclopentadiene (DCPD) in ethylene-propylene-diene (EPDM) terpolymers. They are applicable to diene contents in the
0.1 to 10 mass % range.
1.2 ENB and DCPD are dienes introduced in ethylene/ propylene rubbers to generate specific cure properties. Since high precision for diene content determination has become very important, a Fourier Transform Infrared Spectroscopic (FTIR) method was developed. Diene determination was performed in the past by a refractive index technique. NOTE 1—The procedures for % ENB and % DCPD differ only in the location in the infrared (IR) of the IR peak being quantified.
1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.
1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.
1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.
ASTM D297 Standard Test Methods for Rubber Products-Chemical Analysis
ASTM D3568 Standard Test Methods for Rubber8212;Evaluation of EPDM (Ethylene Propylene Diene Terpolymers) Including Mixtures With Oil
ASTM D3900 Standard Test Methods for Rubber-Determination of Ethylene Units in Ethylene-Propylene Copolymers (EPM) and in Ethylene-Propylene-Diene Terpolymers (EPDM) by Infrared Spectrometry
ASTM D4483 Standard Practice for Determining Precision for Test Method Standards in the Rubber and Carbon Black Industries
ASTM E1421 Standard Practice for Describing and Measuring Performance of Fourier Transform Mid-Infrared (FT-MIR) Spectrometers: Level Zero and Level One Tests
ASTM E168 Standard Practices for General Techniques of Infrared Quantitative Analysis
ASTM E932 Standard Practice for Describing and Measuring Performance of Dispersive Infrared Spectrometers
ASTM D6047-17(2021) history
2021ASTM D6047-17(2021) Standard Test Methods for Rubber, Raw—Determination of 5-Ethylidenenorbornene (ENB) or Dicyclopentadiene (DCPD) in Ethylene-Propylene-Diene (EPDM) Terpolymers
2017ASTM D6047-17 Standard Test Methods for Rubber, Raw&x2014;Determination of 5-Ethylidenenorbornene (ENB) or Dicyclopentadiene (DCPD) in Ethylene-Propylene-Diene (EPDM) Terpolymers
2015ASTM D6047-15 Standard Test Methods for Rubber, Raw&x2014;Determination of 5-Ethylidenenorbornene (ENB) or Dicyclopentadiene (DCPD) in Ethylene-Propylene-Diene (EPDM) Terpolymers
1999ASTM D6047-99(2014) Standard Test Methods for Rubber, Raw—Determination of 5-Ethylidenenorbornene (ENB) or Dicyclopentadiene (DCPD) in Ethylene-Propylene-Diene (EPDM) Terpolymers
1999ASTM D6047-99(2009) Standard Test Methods for Rubber, Raw--Determination of 5-Ethylidenenorbornene (ENB) or Dicyclopentadiene (DCPD) in Ethylene-Propylene-Diene (EPDM) Terpolymers
1999ASTM D6047-99(2003) Standard Test Methods for Rubber, Raw--Determination of 5-Ethylidenenorbornene (ENB) or Dicyclopentadiene (DCPD) in Ethylene-Propylene-Diene (EPDM) Terpolymers
1999ASTM D6047-99e1 Standard Test Methods for Rubber, Raw--Determination of 5-Ethylidenenorbornene (ENB) or Dicyclopentadiene (DCPD) in Ethylene-Propylene-Diene (EPDM) Terpolymers