ASTM C595/C595M-19
Standard Specification for Blended Hydraulic Cements

Standard No.
ASTM C595/C595M-19
Release Date
2019
Published By
American Society for Testing and Materials (ASTM)
Status
Replace By
ASTM C595/C595M-20
Latest
ASTM C595/C595M-23
Scope
1.1 This specification pertains to blended hydraulic cements for both general and special applications, using slag, pozzolan, limestone, or some combination of these, with portland cement or portland cement clinker or slag with lime. NOTE 1—This specification prescribes ingredients and proportions, with some performance requirements, whereas Performance Specification C1157 is a hydraulic cement specification in which performance criteria alone govern the products and their acceptance. 1.2 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard. Values in SI units [or inch-pound units] shall be obtained by measurement in SI units [or inch-pound units] or by appropriate conversion, using the Rules for Conversion and Rounding given in IEEE/ASTM SI 10, of measurements made in other units [or SI units]. Values are stated in only SI units when inch-pound units are not used in practice. 1.3 The text of this standard refers to notes and footnotes, which provide explanatory material. These notes and footnotes (excluding those in tables and figures) are not requirements of the standard. 1.4 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM C595/C595M-19 Referenced Document

  • ASTM C1012 Standard Test Method for Length Change of Hydraulic-Cement Mortars Exposed to a Sulfate Solution
  • ASTM C1038 Standard Test Method for Expansion of Hydraulic Cement Mortar Bars Stored in Water
  • ASTM C109/C109M Standard Test Method for Compressive Strength of Hydraulic Cement Mortars (Using 2-in. or [50-mm] Cube Specimens)
  • ASTM C114 Standard Test Methods for Chemical Analysis of Hydraulic Cement
  • ASTM C1157 Standard Performance Specification for Hydraulic Cement
  • ASTM C150 Standard Specification for Portland Cement
  • ASTM C151 Standard Test Method for Autoclave Expansion of Hydraulic Cement
  • ASTM C1702 Standard Test Method for Measurement of Heat of Hydration of Hydraulic Cementitious Materials Using Isothermal Conduction Calorimetry
  • ASTM C1778 Standard Guide for Reducing the Risk of Deleterious Alkali-Aggregate Reaction in Concrete
  • ASTM C183 Standard Practice for Sampling and the Amount of Testing of Hydraulic Cement
  • ASTM C185 Standard Test Method for Air Content of Hydraulic Cement Mortar
  • ASTM C187 Standard Test Method for Normal Consistency of Hydraulic Cement
  • ASTM C188 Standard Test Method for Density of Hydraulic Cement
  • ASTM C191 Standard Test Method for Time of Setting of Hydraulic Cement by Vicat Needle
  • ASTM C204 Standard Test Methods for Fineness of Hydraulic Cement by Air-Permeability Apparatus
  • ASTM C219 Standard Terminology Relating to Hydraulic and Other Inorganic Cements
  • ASTM C226 Standard Specification for Air-Entraining Additions for Use in the Manufacture of Air-Entraining Hydraulic Cement
  • ASTM C227 Standard Test Method for Potential Alkali Reactivity of Cement-Aggregate Combinations (Mortar-Bar Method)
  • ASTM C311 Standard Test Methods for Sampling and Testing Fly Ash or Natural Pozzolans for Use in Portland-Cement Concrete
  • ASTM C430 Standard Test Method for Fineness of Hydraulic Cement by the 45-956;m (No. 325) Sieve
  • ASTM C465 Standard Specification for Processing Additions for Use in the Manufacture of Hydraulic Cements
  • ASTM C51 Standard Terminology Relating to Lime and Limestone (as Used by the Industry)
  • ASTM C563 Standard Test Method for Optimum SO3 in Hydraulic Cement Using 24-h Compressive Strength
  • ASTM C688 Standard Specification for Functional Additions for Use in Hydraulic Cements
  • ASTM C821 Standard Specification for Lime for Use with Pozzolans
  • IEEE/ASTM SI 10 American National Standard for Metric Practice

ASTM C595/C595M-19 history

Standard Specification for Blended Hydraulic Cements


Copyright ©2024 All Rights Reserved