p-tert-Butylcatechol In Styrene Monomer or AMS (α–Methylstyrene) by Spectrophotometry." >

ASTM D4590-22
Standard Test Method for Colorimetric Determination of p-tert-Butylcatechol In Styrene Monomer or AMS (α–Methylstyrene) by Spectrophotometry

Standard No.
ASTM D4590-22
Release Date
2022
Published By
American Society for Testing and Materials (ASTM)
Latest
ASTM D4590-22
Scope
1.1 This test method is applicable to the determination of residual 4-tertiary-butylcatechol (TBC) in styrene monomer or AMS in the 1 mg ⁄kg to 100 mg ⁄kg range. 1.2 In determining the conformance of the test results using this method to applicable specifications, results shall be rounded off in accordance with the rounding-off method of Practice E29. The limit of detection is 0.2 mg/kg while the limit of quantitation is 0.8 mg/kg based on the ILS data in Table 1. 1.3 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. For specific statements on hazards, see Section 9. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM D4590-22 Referenced Document

  • ASTM D1193 Standard Specification for Reagent Water
  • ASTM D3437 Standard Practice for Sampling and Handling Liquid Cyclic Products
  • ASTM D4790 Standard Terminology of Aromatic Hydrocarbons and Related Chemicals
  • ASTM D6809 Standard Guide for Quality Control and Quality Assurance Procedures for Aromatic Hydrocarbons and Related Materials
  • ASTM E29 Standard Practice for Using Significant Digits in Test Data to Determine Conformance with Specifications
  • ASTM E691 Standard Practice for Conducting an Interlaboratory Study to Determine the Precision of a Test Method

ASTM D4590-22 history

  • 2022 ASTM D4590-22 Standard Test Method for Colorimetric Determination of p-tert-Butylcatechol In Styrene Monomer or AMS (α–Methylstyrene) by Spectrophotometry
  • 2018 ASTM D4590-18 Standard Test Method for Colorimetric Determination of p-tert-Butylcatechol In Styrene Monomer or AMS (α–Methylstyrene) by Spectrophotometry
  • 2013 ASTM D4590-13 Standard Test Method for Colorimetric Determination of p-tert-Butylcatechol In Styrene Monomer or AMS (alpha;ndash;Methylstyrene) by Spectrophotometry
  • 2009 ASTM D4590-09 Standard Test Method for Colorimetric Determination of p-tert-Butylcatechol In Styrene Monomer or AMS (alpha-Methylstyrene) by Spectrophotometry
  • 2006 ASTM D4590-06 Standard Test Method for Colorimetric Determination of p-tert-Butylcatechol In Styrene Monomer or AMS (alpha-Methylstyrene) by Spectrophotometry
  • 2000 ASTM D4590-00 Standard Test Method for Colorimetric Determination of p-tert-Butylcatechol In Styrene Monomer or AMS (alpha-Methylstyrene) by Spectrophotometry
  • 1995 ASTM D4590-95A Standard Test Method for Colorimetric Determination of p-tert-Butylcatechol In Styrene Monomer or AMS (alpha-Methylstyrene) by Spectrophotometry
Standard Test Method for Colorimetric Determination of <emph type="ital">p-tert</emph >-Butylcatechol In Styrene Monomer or AMS (α–Methylstyrene) by Spectrophotometry



Copyright ©2024 All Rights Reserved