ASTM C1359-18e1
Standard Test Method for Monotonic Tensile Strength Testing of Continuous Fiber-Reinforced Advanced Ceramics With Solid Rectangular Cross Section Test Specimens at Elevated Temperatures

Standard No.

ASTM C1359-18e1

Release Date

2018

Published By

American Society for Testing and Materials (ASTM)

Latest

ASTM C1359-18e1

Scope

1.1 This test method covers the determination of tensile strength, including stress-strain behavior, under monotonic uniaxial loading of continuous fiber-reinforced advanced ceramics at elevated temperatures. This test method addresses, but is not restricted to, various suggested test specimen geometries as listed in the appendixes. In addition, test specimen fabrication methods, testing modes (force, displacement, or strain control), testing rates (force rate, stress rate, displacement rate, or strain rate), allowable bending, temperature control, temperature gradients, and data collection and reporting procedures are addressed. Tensile strength as used in this test method refers to the tensile strength obtained under monotonic uniaxial loading, where monotonic refers to a continuous nonstop test rate with no reversals from test initiation to final fracture. 1.2 This test method applies primarily to advanced ceramic matrix composites with continuous fiber reinforcement: unidirectional (1D), bidirectional (2D), and tridirectional (3D) or other multi-directional reinforcements. In addition, this test method may also be used with glass (amorphous) matrix composites with 1D, 2D, 3D, and other multi-directional continuous fiber reinforcements. This test method does not directly address discontinuous fiber-reinforced, whiskerreinforced, or particulate-reinforced ceramics, although the test methods detailed here may be equally applicable to these composites. 1.3 The values stated in SI units are to be regarded as the standard and are in accordance with IEEE/ASTM SI 10. 1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. Refer to Section 7 for specific precautions. 1.5 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM C1359-18e1 Referenced Document

• ASTM C1145 Standard Terminology of Advanced Ceramics
• ASTM D3379 Standard Test Method for Tensile Strength and Young's Modulus for High-Modulus Single-Filament Materials
• ASTM D3878 Standard Terminology Composite Materials
• ASTM D6856/D6856M Standard Guide for Testing Fabric-Reinforced “Textile” Composite Materials*， 2023-11-01 Update
• ASTM E1012 Standard Practice for Verification of Specimen Alignment Under Tensile Loading
• ASTM E21 Standard Test Methods for Elevated Temperature Tension Tests of Metallic Materials
• ASTM E220 Standard Test Method for Calibration of Thermocouples By Comparison Techniques
• ASTM E337 Standard Test Method for Measuring Humidity with a Psychrometer (the Measurement of Wet- and Dry-Bulb Temperatures)
• ASTM E4 Standard Practices for Force Verification of Testing Machines
• ASTM E6 Standard Terminology Relating to Methods of Mechanical Testing
• ASTM E83 Standard Practice for Verification and Classification of Extensometer
• IEEE/ASTM SI 10 American National Standard for Metric Practice

ASTM C1359-18e1 history

• 2018 ASTM C1359-18e1 Standard Test Method for Monotonic Tensile Strength Testing of Continuous Fiber-Reinforced Advanced Ceramics With Solid Rectangular Cross Section Test Specimens at Elevated Temperatures
• 2018 ASTM C1359-18 Standard Test Method for Monotonic Tensile Strength Testing of Continuous Fiber-Reinforced Advanced Ceramics with Solid Rectangular Cross Section Test Specimens at Elevated Temperatures
• 2013 ASTM C1359-13 Standard Test Method for Monotonic Tensile Strength Testing of Continuous Fiber-Reinforced Advanced Ceramics With Solid Rectangular Cross-Section Test Specimens at Elevated Temperatures
• 2011 ASTM C1359-11 Standard Test Method for Monotonic Tensile Strength Testing of Continuous Fiber-Reinforced Advanced Ceramics With Solid Rectangular Cross-Section Test Specimens at Elevated Temperatures
• 2005 ASTM C1359-05 Standard Test Method for Monotonic Tensile Strength Testing of Continuous Fiber-Reinforced Advanced Ceramics With Solid Rectangular Cross-Section Test Specimens at Elevated Temperatures
• 1996 ASTM C1359-96(2000) Standard Test Method for Monotonic Tensile Strength Testing of Continuous Fiber-Reinforced Advanced Ceramics With Solid Rectangular Cross-Section Specimens at Elevated Temperatures