ASTM D7269/D7269M-11
Standard Test Methods for Tensile Testing of Aramid Yarns

Standard No.
ASTM D7269/D7269M-11
Release Date
2011
Published By
American Society for Testing and Materials (ASTM)
Status
Replace By
ASTM D7269/D7269M-17
Latest
ASTM D7269/D7269M-20
Scope

The levels of tensile properties obtained when testing aramid yarns and cords are dependent on the age and history of the specimen and on the specific conditions used during the test. Among these conditions are rate of stretching, type of clamps, gage length of specimen, temperature and humidity of the atmosphere, rate of airflow across the specimen, and temperature and moisture content of the specimen. Testing conditions accordingly are specified precisely to obtain reproducible test results on a specific sample.

Because the force-bearing ability of a reinforced product is related to the strength of the yarn or cord used as a reinforcing material, breaking strength is used in engineering calculations when designing various types of textile reinforced products. When needed to compare intrinsic strength characteristics of yarns or cords of different sizes or different types of fiber, breaking tenacity is very useful because, for a given type of fiber, breaking force is approximately proportional to linear density.

Elongation of yarn or cord is taken into consideration in the design and engineering of reinforced products because of its effect on uniformity of the finished product and its dimensional stability during service.

The FASE is used to monitor changes in characteristics of the textile material during the various stages involved in the processing and incorporation of yarn or cord into a product.

Modulus is a measure of the resistance of yarn or cord to extension as a force is applied. It is useful for estimating the response of a textile reinforced structure to the application of varying forces and rates of stretching. Although modulus may be determined at any specified force, initial modulus is the value most commonly used.

Work-to-break is dependent on the relationship of force to elongation. It is a measure of the ability of a textile structure to absorb mechanical energy. Breaking toughness is work-to-break per unit mass.

It should be emphasized that, although the preceding parameters are related to the performance of a textile-reinforced product, the actual configuration of the product is significant. Shape, size, and internal construction also can have appreciable effect on product performance. It is not possible, therefore, to evaluate the performance of a textile reinforced product in terms of the reinforcing material alone.

If there are differences of practical significance between reported test results for two laboratories (or more), comparative tests should be performed to determine if there is a statistical bias between them, using competent statistical assistance. As a minimum, test samples should be used that are as homogeneous as possible, that are drawn from the material from which the disparate test results were obtained, and that are randomly assigned in equal numbers to each laboratory for testing. Other materials with established test values may be used for this purpose. The test results from the two laboratories should be compared using a statistical test for unpaired data, at a probability level chosen prior to the testing series. If a bias is found, either its cause must be found and corrected, or future test results must be adjusted in consideration of the known bias.

1.1 These test methods cover the tensile testing of aramid yarns, cords twisted from such yarns, and fabrics woven from such cords. The yarn or cord may be wound on cones, tubes, bobbins, spools, or beams; may be woven into fabric; or may be in some other form. The methods include testing procedure only and include no specifications or tolerances.

1.2 The values stated in either SI units or inch-pound units are to be regar......

ASTM D7269/D7269M-11 Referenced Document

  • ASTM D123 Standard Terminology Relating to Textiles*， 2023-09-14 Update
  • ASTM D1776 Standard Practice for Conditioning and Testing Textiles
  • ASTM D1907 Standard Test Method for Linear Density of Yarn (Yarn Number) by the Skein Method
  • ASTM D1909 Standard Table of Commercial Moisture Regains for Textile Fibers
  • ASTM D2258 Standard Practice for Sampling Yarn for Testing
  • ASTM D4848 Standard Terminology Related to Force, Deformation and Related Properties of Textiles*， 2018-09-01 Update
  • ASTM D6587 Standard Test Method for Yarn Number Using Automatic Tester*， 2024-04-20 Update
  • ASTM D76 Standard Specification for Tensile Testing Machines for Textiles

ASTM D7269/D7269M-11 history

Standard Test Methods for Tensile Testing of Aramid Yarns


Copyright ©2024 All Rights Reserved